Flange Type Tension Detector

Flange Type Tension Detector

Digital motor actuator controller. 

It uses a motor rather than hydraulics, so clean and quick control is possible without worrying about oil leak, and is can provide a safe and optimized work environment by more simplified sensor calibration and operation, alarms in case of emergency and powerful protective functions. 

(※Electrostatic Discharge KN6100-4-2 Level 3 passed)

Digital hydraulic cylinder controller. 

Digital motor actuator controller.

As it uses a motor, not a cylinder, it is clean with no oil leakage and can be quickly controlled. 

It enables diverse control of the system because CPC function is added to the basic EPC function, and provides more optimized work environment as detail setting function is added to enable advanced setting suitable for the environment.

Digital hydraulic cylinder controller.

It can control guides of a large capacity using powerful force as a hydraulic unit, not a motor, is used. 

It enables diverse control of the system because CPC function is added to the basic EPC function, and provides more optimized work environment as detail setting function is added to enable advanced setting suitable for the environment.

It is a sensor in which multiple infrared elements are linearly arranged to enable a wider range of edge detection, and suitable for detecting the exact position of papers, non-woven fabrics and light impermeable homogeneous substances.  

It is a sensor in which multiple infrared elements are linearly arranged to enable a wider range of edge detection, and suitable for detecting the exact position of papers, non-woven fabrics and light impermeable homogeneous substances.  

It is a sensor in which multiple infrared elements are linearly arranged to enable a wider range of edge detection, and suitable for detecting the exact position of papers, non-woven fabrics and light impermeable homogeneous substances.  

This guide roller directs the material to the exact position before it reaches the printing point or cutting point.

·It is recommended to use an aluminum roller.

·Design the roller as a guide type roller not a drum type. 

·For the MCD type(motor type), a motor actuator is built in.

·For the HCD type(cylinder type), a cylinder is built in. 

EPC/CPC system seeking for easy-to-use, cost and performance.

It is a center pivot type with a small load of materials, which is an all-in-one product in which a guide, controller and sensor are integrated. 

Quick and precise control is possible. 

(※ The sensor in the product photo is sold separately.)  

(※ The position of the sensor and the position of the controller panel can be changed as per the request of customer.)

EPC/CPC system seeking for easy-to-use, cost and performance.

It is a center pivot type with a small load of materials, which is an all-in-one product in which a guide, controller and sensor are integrated. 

Quick and precise control is possible.

(※ The sensor in the product photo is sold separately.) 

(※ The position of the sensor and the position of the controller panel can be changed at the request of the customer.)  

Prompt and accurate control can be achieved by using a motor.

It is operated by electricity and can be used without difficulty as there is no possibility of oil leakage unlike a hydraulic type.

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup, and differential pickup sensor values.​ 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup, and differential pickup sensor values.​ 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values. 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values. 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values.

PR-DTC-4000CP has a built-in power (SMPS). 

The PTC-303D is a digital automatic tension controller to control power brake and clutch automatically.  

It does not use a tension detector but increases or decreases the output of powder brake or powder clutch in proportion to the fabric’s length to control the tension. 

It is an open loop type semiautomatic tension control device. 

The proximity sensor is installed to detect the number of revolutions of the general roller at the front of winders and unwinders. 

It does not use a tension detector but increases or decreases the output of powder brake or powder clutch in proportion to the fabric’s length to control the tension. It is an open loop type semiautomatic tension control device. The proximity sensor is installed to detect the number of revolutions of the general roller at the front of winders and unwinders. PR-DTC-3000P has a built-in power (SMPS). 

It does not use a tension detector but uses the thickness and the number of revolutions of fabric to increase or decrease the output of powder brake or powder clutch to control the tension.

It is an open loop type semiautomatic tension control device. 

The proximity sensor is installed to directly detect the number of revolutions of winders and unwinders. 

It uses a variable resistor or ultrasonic distance measuring sensor to check the amount of winding and unwinding to control. 

It does not use a tension detector but uses the thickness and the number of revolutions of fabric to increase or decrease the output of powder brake or powder clutch to control the tension.

It is an open loop type semiautomatic tension control device. The proximity sensor is installed to directly detect the number of revolutions of winders and unwinders. 

It uses a variable resistor or ultrasonic distance measuring sensor to check the amount of winding and unwinding to control. 

This is a manual tension controller which controls the powder brake and the powder clutch. 

This is the panel mounted model of PR-DTC-2000.

The control part and the main body are separated so that it can be mounted on a panel.

The large powder brake and the powder clutch are manually controlled.  

This is the panel mounted model of PR-DTC-2100.

The control part and the main body are separated so that it can be mounted on a panel.

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Left ↔ Right detection 

PRTL-FC Type is a Flange load cell which is compact type.

It can detect tension with high precision since the location of materials on rollers doesn't affect tension detection and there is no hysteresis. 

Besides, it is very easy to install irrespective of unwinding or rewinding and able to compatible with all types of load cell. ​ 

Powder Brake (Hollow Type, Natural Air Cooled Type) 

Powder Brake (Natural Air Cooled Type) 

Powder Brake (Natural Air Cooled Type) 

Powder Clutch (Outside Radiating Type) 

Powder Clutch (High capacity) 

Powder Clutch (Natural Air Cooled Type) 

Powder Clutch (Natural Air Cooled Type) 

Powder Clutch (Natural Air Cooled Type)