Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup, and differential pickup sensor values.​ 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup, and differential pickup sensor values.​ 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values. 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values. 

Digital Tension Controller, a model which controls the powder brake or the powder clutch after reading the load cell, pickup sensor values.

PR-DTC-4000CP has a built-in power (SMPS). 

The PTC-303D is a digital automatic tension controller to control power brake and clutch automatically.  

It does not use a tension detector but increases or decreases the output of powder brake or powder clutch in proportion to the fabric’s length to control the tension. 

It is an open loop type semiautomatic tension control device. 

The proximity sensor is installed to detect the number of revolutions of the general roller at the front of winders and unwinders. 

It does not use a tension detector but increases or decreases the output of powder brake or powder clutch in proportion to the fabric’s length to control the tension. It is an open loop type semiautomatic tension control device. The proximity sensor is installed to detect the number of revolutions of the general roller at the front of winders and unwinders. PR-DTC-3000P has a built-in power (SMPS). 

It does not use a tension detector but uses the thickness and the number of revolutions of fabric to increase or decrease the output of powder brake or powder clutch to control the tension.

It is an open loop type semiautomatic tension control device. 

The proximity sensor is installed to directly detect the number of revolutions of winders and unwinders. 

It uses a variable resistor or ultrasonic distance measuring sensor to check the amount of winding and unwinding to control. 

It does not use a tension detector but uses the thickness and the number of revolutions of fabric to increase or decrease the output of powder brake or powder clutch to control the tension.

It is an open loop type semiautomatic tension control device. The proximity sensor is installed to directly detect the number of revolutions of winders and unwinders. 

It uses a variable resistor or ultrasonic distance measuring sensor to check the amount of winding and unwinding to control. 

This is a manual tension controller which controls the powder brake and the powder clutch. 

This is the panel mounted model of PR-DTC-2000.

The control part and the main body are separated so that it can be mounted on a panel.

The large powder brake and the powder clutch are manually controlled.  

The powder brake and the powder clutch are manually controlled. 

This is the panel mounted model of PR-DTC-2100.

The control part and the main body are separated so that it can be mounted on a panel.

This is a manual tension controller which controls the powder brake and the powder clutch. 

It is an operating panel which can be connected with PR-DTC-2200 to use. 

Through this operating panel, the control output of PR-DTC-2200 can be adjusted. 

This is a tension controller for steel products which controls a powder brake or powder clutch of large capacity. 

It is a load cell type digital tension gauge.  
Being small, it allows easy utilization of space, and can be simply set.

It outputs precise voltage and current at the same time for inverter control.

It is a digital tension gauge with built in high performance converter.
It is compatible with both a load cell type tension detector and a pick-up type (LVDT) tension detector. 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Down detection 

Tension detection direction: Left ↔ Right detection

Tension detection direction: Left ↔ Right detection 

Flange Type Tension Detector

Flange Type Tension Detector

PRTL-FC Type is a Flange load cell which is compact type.

It can detect tension with high precision since the location of materials on rollers doesn't affect tension detection and there is no hysteresis. 

Besides, it is very easy to install irrespective of unwinding or rewinding and able to compatible with all types of load cell. ​ 

Powder Brake (Hollow Type, Natural Air Cooled Type) 

Powder Brake (Hollow Type, Water Cooled Type) 

Powder Brake (Outside Radiating Type) 

Powder Brake (Natural Air Cooled Type) 

Powder Brake (Natural Air Cooled Type) 

Powder Brake (Natural Air Cooled Type, Short Type) 

Powder Brake (Forced Air Cooled Type) 

Powder Brake (Indirect Water Cooled Type) 

Powder Clutch (Outside Radiating Type) 

Powder Clutch (High capacity) 

 ​Powder Clutch (One shaft type-Quill shaft)​​

Powder Clutch (Natural Air Cooled Type) 

Powder Clutch (Natural Air Cooled Type) 

Powder Clutch (Natural Air Cooled Type) 

Powder Clutch (Special Cooling Type) 

Powder Clutch (One shaft type-Solid shaft)